Portable Moisture Meter

   
««First   «Prev   [1]  [2]  [3]  [4]  [5]  [6]  [7]  [8]  [9]  Next»  Last»»
The Skipper Plus Moisture Meter
Tramex The Skipper Plus Moisture Meter

Product Features
 
  • Tramex The Skipper Plus Moisture Meter for detecting excess moisture in GRP and wooden boats.
  • A pocket sized meter, the Skipper is designed to locate moisture in boat hulls and fittings.
  • Three ranges for detecting moisture in GRP and Hardwood for salt & freshwater.
  • Wide range of readings for wood of 5% to 30% on hard wood scale and 0 to 100 on comparative scale for GRP and other materials
  • Identifies the presence of Osmosis in Fibreglass Hulls.
  • Confirms if wooden boats are dry enough for painting or varnishing.
  • Trace deck and bulkhead leaks.
  • “Hold” function facilitates ease of recording readings
  • Soft rubber electrodes make direct contact without scratching.
  • No Pins, No Probes, No Scratching.
  • High moisture audio warning tone that can be switched on or off.
  • Battery operated (included) 






DEC Scanner
Tramex DEC Scanner

Product Features
 
  • Tramex DEC Scanner for quick scanning of large roof areas with instant, accurate results.
  • Three ranges of sensitivity.
  • Able to detect as little as 2% excess moisture.
  • Instantaneous, clear indications of roof conditions.
  • Continuous operation for uninterupted coverage.
  • Locates boundaries of wet areas in minutes.
  • More than twice as fast as nuclear meters.
  • Able to test thinner roofs.
  • No license required.
  • A fraction of the cost of airborne and on the roof infra-red systems. Easy to use, no training required.
  • Dependable solid state circuitry and rugged molded case for long-term reliability.
  • Heavy duty Aluminium flight case.
  • Shoulder strap, survey pad and instructions.
  • Battery powered (included). 






CMEX Hygro-I Flooring Kit
Tramex CMEX Hygro-I Flooring Kit

Product Features
 
  • Tramex CMEX Hygro-I Flooring Kit the complete moisture & humidity testing kit for concrete and wood.
  • Incorporating the Tramex instant moisture test and the new Hygro-i in-situ probe working together to provide a new standard in speed & accuracy which can be used again & again.
  • CMEXpertII gives instant non-destructive readings in concrete up to 6.9% moisture content.
  • Backlit display for easy viewing in low light conditions.
  • Use per ASTM F2659.
  • Hygro-i NEW reusable NIST traceable relative humidity probe.
  • The Hygro-i sensor is fast, accurate, reusable and economical.
  • Wood probe for wood moisture content readings. 






Compact Kit
Tramex Compact Kit

Product Features
 
  • Tramex Compact Kit complete package for moisture testing in wood, wood by-products and other building materials, such as plaster / brick, and plasterboard (drywall).
  • Wide moisture content range: Up to 40% on wood.
  • Clear Analog Display.
  • Built-in Pins
  • Timed On/Off Switch.
  • Reading Hold facility.
  • Temperature stable circuit.
  • Heavy-duty yet light-weight Aluminium construction.
  • Built-in battery check.
  • Battery powered (supplied)

 







Concrete Hygro-I Inspection Kit
Tramex Concrete Hygro-I Inspection Kit

Product Features
 
  • Tramex Concrete Hygro-I Inspection Kit complete moisture & humidity testing kit for concrete.
  • Incorporating the Tramex instant moisture test and the new Hygro-i in-situ probe working together to provide a new standard in speed & accuracy which can be used again & again.
  • CMEXpertII gives instant non-destructive readings in concrete up to 6.9% moisture content.
  • Backlit display for easy viewing in low light conditions.
  • Use per ASTM 2659.
  • Hygro-i NEW reusable NIST traceable relative humidity prob.
  • The Hygro-i sensor is fast, accurate, reusable and economical.  






Flooring Hygro-I Master Kit
Tramex Flooring Hygro-I Master Kit

Product Features
 
  • Tramex Flooring Hygro-I Master Kit complete package for moisture testing of Concrete and Wood Flooring.
  • CME4 gives instant non-destructive readings in concrete up to 6 % moisture content.
  • Relative scale of 0-100 for other building materials including drywall, laminate, residential asphalt shingles and masonry products.
  • Use per ASTM F2659.
  • MRH III non-destructive moisture meter with built in wood specific gravity species correction.
  • Reads 1 ¼” deep in wood.
  • Backlit display for easy viewing in low light conditions.
  • Plug in hand & hammer wood probes for invasive testing.
  • Hygro-i NEW reusable NIST traceable relative humidity probe 






MRH III Hygro-I Kit
Tramex MRH III Hygro-I Kit

Product Features
 
  • Tramex MRH III Hygro-I Kit complete package for moisture and humidity measurement of the building envelope.
  • Incorporating 3 modes of operation : non invasive moisture content testing of wood, plug in heavy duty wood pin probe with extra insulated 7” (200mm) pins for deep wall probing and plug in Hygro-i Humidity Probe for Relative
  • Relative scale of 0-100 for other building materials including drywall, laminate, residential asphalt shingles and masonry products.
  • Humidity, Temperature, Dew Point and Mixing Ratio readings.
  • MRH III - non-destructive moisture meter with built in wood specific gravity species correction.
  • Reads 1 ¼” deep in wood.
  • Backlit display for easy viewing in low light conditions.

  •  






MC4000 In-Kiln Moisture Measurement System
Wagner MC4000 In-Kiln Moisture Measurement System

Product Features
 
  • Displays moisture content of lumber above and below the fiber saturation point.
  • Provides moisture content measurement for kiln temperature ranges of 70º- 300º.
  • Large sensing zone to obtain average moisture content between sensors.
  • Minimizes or eliminates inefficient manual hot checks therefore reducing labor costs.
  • Automatic kiln shut-down and alarm based on the moisture content level within 1% MC.
  • Open architecture integrates with virtually any computerized kiln controller.






Omega In-Line Moisture Measurement System
Wagner Omega In-Line Moisture Measurement System

Product Features
 
  • Large Display Terminal allow quick and easy monitoring from multiple vantage points.
  • Wagner Omega In-Line Moisture Measurement System able to see settings both at the computer and on the Omega console, such as: avg/peak, chain speed, any alarm setting and MC for marker.
  • Run (or batch) reports- these user can also see both at the computer and on the Omega console and can be viewed by anyone tied to the LAN network.
  • Unit (or pack) reports coupled with Kiln charge reports- the data in these reports can be sorted by date, kiln, or lumber product.
  • Trend reports and Color Graphing- Trend and graph user kiln performance over time to maximize user lumber drying quality control.
  • Kiln view screen- shows where wood is not being dried properly in the kiln so adjustments can be made to improve kiln drying performance and decrease time in the kiln.






BI2200 Building Inspection Moisture Meter
Wagner BI2200 Building Inspection Moisture Meter

Product Features
 
  • A non-invasive tool for measuring a wide range of materials including wood, synthetic stucco, plaster, drywall, insulation materials, ceramic tile, shingles, linoleum, concrete and more.
  • Wagner BI2200 Building Inspection Moisture Meter can compare and pinpoint elevated MC problem areas or conditions by establishing a known baseline dry MC relative reading on a building material
  • Programmable for numerous building materials and its two-button control makes one-handed operation simple.
  • Designed with a Teflon pad to protect the sensor area on rough or abrasive surfaces.
  • Size: Length – 4 9/16"; Width – 2 3/4"; Height – 1 1/16"
  • Weight – .37 lbs
  • Power – 9 volt battery
  • Auto Power Shut Down – 60 seconds
  • Depth of Measurement: 3/4"
  • Moisture Content: Relative 5 – 30
  • Scanning Area: 1 1/2" x 2 1/2"
  • Material Setting: Selectable setting .20 – 1.0
  • Calibration verifiable at factory
  • Battery Included
  • Shock Resistant Carry Case with Belt Clip Included